calls
furniture the hands how to make furniture the hands furniture the hands - the main page the main page - furniture the hands furniture manufacturing by the hands furniture manufacturing by own strength
offers on furniture manufacturing by the hands how to make furniture the hands furniture the hands, articles furniture the hands, councils recommendations how to make furniture the hands councils how to make furniture the hands furniture the hands a management how to make furniture the hands
calls

When phone

Not always the telephone wire comes to an end there where there is this or that piece of furniture intended for installation of phone. But nobody prevents to put us furniture there where phone is established. We bring to your attention three variants of the decision of this problem.

The Most simple decision is the small wall shelf (in drawing at the left). Its sizes are defined by the sizes of phone. For shelf manufacturing are required: the wall board connected to it a horizontal shelf some bolshego of the size and a regiment on which actually phone also takes places. All parts strongly incorporate among themselves wooden shkantami or the screws which are screwed up in horizontal shelves from an underside of a wall board. In quality. Supports between regiments it is possible to use two fine-moulded legs from an old case; preliminary necessarily it is necessary to check up, whether has spoilt their wood zhuchok. For the same purposes it is possible to use the narrow high whatnot (drawing on the right see). .

As a material it is possible to use wood from the old, well remained furniture or drevesnostruzhechnye plates (DSP), in the thickness approximately 2 see For legs we take a round timber, however it is possible to use, for example, sticks from brooms. In plates we bore through apertures, it is far enough from edges that wood has not cracked. Apertures should correspond to diameter of a stick. In three bottom regiments it is done through apertures. At last from the bottom shelves the aperture becomes on half of thickness of a shelf. At the small shelf which are over it, the aperture also is made from above on half of thickness; at the uppermost shelf the aperture is made also on half of thickness of a shelf, but from below. Regiments should correspond to these apertures precisely. .

As support for shelves it is offered to use the metal pins which are reaching the middle of shelves and coming out approximately on 2см. For this purpose it is possible to take thick long nails and to file their saw for are sharp metal till the demanded length. The arrangement of pins is specified in average drawing on the right. At installation the bottom pin in the beginning is hammered, and then on it the board keeps within. In the same sequence other regiments are established. For bolshej stability of a rack stick together with regiments. .

In the third case (average drawing at the left see) installation is made the same as in the previous design, and the design differs from previous only under the form. This variant is recommended when is available enough place and the right part of the top shelf it is possible to use as a support for colours.

The House master always should think of expedient use of the rests of wood, after all it is possible to make various useful trifles of the rests.

In the bottom drawing the example as it is possible to use the wood rests is resulted. From round reek at different works there are pieces of various length, for example, when cut till the necessary length of a stick from shovels and brooms or change the old broken stick for the new. It is possible to use here too branches and the boughs remaining at a scrap of fruit-trees or it is simple, picked up in wood. The truth in this case wood needs to be prepared in appropriate way even for work, i.e. to remove a bark and to process a round surface. .

As it is specified in drawing, it is possible to make of the rests of round wood, for example, a support for smoking subjects. Five scraps of wood are packed so that it was possible to stick together strongly them, among themselves. Before it it is necessary to prepare separate parts of this design. For this purpose it is required to drill from above apertures of various depth. In them the lighter, the adaptation for stuffing of tubes are located ershiki for procleaning of tubes. The apertures drilled sideways, serve for placing of tubes. However it is possible also, to place them how it is shown in the bottom drawing. .

If separate parts of a support it is planned to process morilkoj or to paint different colours, it is recommended to do it before pasting. If the support is supported by a shelf from the thin plywood, a bit supporting edges, it raises uchtojchivost all design even more.
If separate parts of a support it is planned to process morilkoj or to paint different colours, it is recommended to do it before pasting. If the support is supported by a shelf from the thin plywood, a bit supporting edges, it raises uchtojchivost all design even more.

ARE NECESSARY