grow up
furniture the hands how to make furniture the hands furniture the hands - the main page the main page - furniture the hands furniture manufacturing by the hands furniture manufacturing by own strength
offers on furniture manufacturing by the hands how to make furniture the hands furniture the hands, articles furniture the hands, councils recommendations how to make furniture the hands councils how to make furniture the hands furniture the hands a management how to make furniture the hands
grow up

When children

Constantly there is a question. How is better to equip a room for two children? The children, the nastojatelnee necessity practical become more senior decisions of this question. Friends of children on a visit come, the place that it was possible for them to dance and not to feel the constrained therefore is necessary. It means that a floor surface, how much only is possible, should be free from furniture. If thus it is a question of a room in the new house where length of a premise - four with superfluous metre, and width - a bit more than two metres, it is necessary to use any possibility for the most expedient equipment of a room according to the above-named requirements.

The Best "ё=Ёюш=хыіэющ яыюЁрфъющ" for this purpose there will be room walls. Thus we use a variant with folding beds which take places in the bottom branch of a rack and are in front closed by a curtain. An element of the rational equipment of a room is also the sliding table at which it will be convenient to sit. In this case the variant with oven heating, but if in apartment the central heating, for it also is required the certain area is considered. In drawings the basic bastings of how the room should be equipped, and, certainly are given only, it is required to develop various variants as, for example, in rooms of the identical sizes of a door can be located differently. .

According to depth of a folding bed depth (40 sm) wall case offered by us on height reaching a ceiling is maintained also. Depth of shelves recommended by us should not exceed 25 the Case on width see shares on three parts. Each branch has - width 50-60 the Case see is made of four vertically located frames made with necessary intermediate cross-section inserts from reek in the thickness of 2 sm and in the width 8-10 see .

Angular connections are carried out by means of thorns and eyes. Necessary stability is reached and at connection vnahlestku. We can quite refuse a back wall of a case.

Direct frames rally by means of cross-section connection. Necessary plug-in regiments also strongly incorporate to a frame by means of screws, accordingly nails thereby to give designs still the big stability. Connection with a room wall is better to make by means of probes. Below under a case the socle is established, approximately 10 sm, from above a cover which thickness approximately 4 see Doors also are made by height of the frames which have been pasted over with a firm wood-fiber plate (TDVP), accordingly from a strong material, for example from kleenoj wood, plywood plates or drevesnostruzhechnyh plates (DSP). They are established between frames limiting them and fasten on rojalnyh loops. .

The Regiments located on a wall of a case, and also on a free part of a wall near to the bed located opposite are made by a principle of boxes, equipped with back walls and fasten to a wall flat probes. The basic support of the case occupying a wall where there is a door (see the top drawing), the vertical racks leaning against a frame issued in the form of a locker of a folding bed are. The top rooms going on all length the cross-section shelf is nailed up to vertical racks. The bottom branches strongly incorporate with vertical bokovinami to the help shkantov. .

The Described way of manufacturing demands at connection of gradual advancement from one party of a room to another. The part of shelves is closed dverkami. They should be made by the same principle, as dverki cases. dverok it is possible to paste over the forward parties with the same wall-paper which were used for walls or to coat, sharply different on colour from frame edges. .

the Bottom drawing shows a variant of internal division of a case. It is possible to build in the right part also one or two drawers. A coat hanger for outer clothing is located in such a manner that in the left compartment jackets and blouses, and on the average - trousers and a coat take places.
the Bottom drawing shows a variant of internal division of a case. It is possible to build in the right part also one or two drawers. A coat hanger for outer clothing is located in such a manner that in the left compartment jackets and blouses, and on the average - trousers and a coat take places.