furniture the hands how to make furniture the hands furniture the hands - the main page the main page - furniture the hands furniture manufacturing by the hands furniture manufacturing by own strength
offers on furniture manufacturing by the hands how to make furniture the hands furniture the hands, articles furniture the hands, councils recommendations how to make furniture the hands councils how to make furniture the hands furniture the hands a management how to make furniture the hands

the Small house workshop

the House workshop takes places usually in a cellar, a closet of apartment or a shed, and in it, as a rule, there is not enough place. To equip a workshop, using the minimum area - it is very tempting, though, of course, it is easier to speak about it, than to make. Therefore available area needs to be used with the maximum rationality, having placed the equipment to the ceiling. The truth here arises a new problem: everything that is required for those or other works, should be placed conveniently. In a variant offered by us we start with that principle that the subjects used rather seldom, for example, banks with a paint and other equipment for painting works should be placed on the top regiments. .

Nails, screws, a box with any trifle etc. need to be placed in the bottom part of our small workshop. At designing it is necessary not to forget to allocate a place for reek (shtaketnika), small boards. However the most important - correctly to place tools which are required more often. They need to be concentrated in a small compartment and well to fix; at the same time, in case of need, they should act in film easily. Besides the small board on which it is possible to perform the work which is not demanding many place is required to us.

The workshop Offered by us can be made in the form of the big case. It is desirable even that this case was locked, however basically it is enough and a rigid frame design from reek. In our example we provide a design executed in the form of a case. .

The Sizes of a design, its height, width and depth are defined by necessary conditions and available possibilities; however depth of a case should be not less than 50-60 These sizes see are established not only more to place. The main condition is that sliding walls on which tools take places, and a board on which works are made, should have corresponding depth. Some instructions, concerning features of the equipment of a case, do not provide any changes in the relation of placing of shelves which as usually, settle down on strong, basic rejkah and reliably incorporate to lateral faces. .

That rejki, bruski and other details did not drop out of wood from the compartment taken away for them (in the basic drawing - at the left), it is possible to establish a small cross-section beam. For this purpose it is necessary to cut two kolodki in the form of the Latin letter "U" corresponding to a thickness locking rejki and to screw them or to nail up at desirable height on a compartment inside. Rejku we put from above and when it is necessary, we take out. Kolodki-holders it is possible not to cut, and to hammer together from three bruskov everyone. .

Distances between partitions are established so that the mobile Walls could be put forward and pushed easily back. The stopper does not give to a wall To leave completely. The similar principle, only in a horizontal variant, is provided And for a working board which can move between two regiments. An arrangement Tools on sliding walls everyone should think over itself. Important only that, That distances between walls allowed to place conveniently and bulky tools. For reliable placing of tools on walls it is possible to make loops of the rests Leather belt or belt. It is possible to make also corresponding devices with the help reek or bruskov. .

the Rack can be increased till the desirable sizes at width and height. Small jashchichki for nails, screws or other small subjects it is possible to establish so that they were put forward on specially made frames, and it is possible to put simply separate jashchichki against each other. If the branch space is used thus completely, jashchichki stand in a rack densely and do not fall down from it.
the Rack can be increased till the desirable sizes at width and height. Small jashchichki for nails, screws or other small subjects it is possible to establish so that they were put forward on specially made frames, and it is possible to put simply separate jashchichki against each other. If the branch space is used thus completely, jashchichki stand in a rack densely and do not fall down from it.