furniture the hands how to make furniture the hands furniture the hands - the main page the main page - furniture the hands furniture manufacturing by the hands furniture manufacturing by own strength
offers on furniture manufacturing by the hands how to make furniture the hands furniture the hands, articles furniture the hands, councils recommendations how to make furniture the hands councils how to make furniture the hands furniture the hands a management how to make furniture the hands

the Small dining room in a kitchen corner

Kitchens in some old apartments have rather original forms, and it is necessary to break thoroughly a head to think up, as them to convert. Especially problematic there is a situation when it is found out that all rooms as frequently happens in old apartments, checkpoints. Then it is necessary to enter into a living room through kitchen that is the extremely inconvenient. In this case, following a national saying, to make of need virtue, differently from inconvenience convenience, not so it is simple. It is necessary to find an optimum variant of division of a kitchen premise on podsobku, actually kitchen and a dining room.

In the given section it will be a question of how in a narrow aperture between a window and a wall to allocate a corner and to equip from it a small dining room. Certainly, our imagination can be here boundless, however two elements at the equipment of this corner of kitchen should be obligatory: a rack separating it from the basic part of kitchen and pristennyj a table. .

In the beginning we will talk about a rack. Apparently in the top drawing it goes from the end of an oblique wall deep into kitchens. Its sizes are defined by spatial possibilities of a premise. In our case length of a rack-approximately of 120 sm, width of separate shelves 25-30 see Two bottom shelves of a rack it is possible to equip as a little table and to make them more long in comparison with other regiments. The thickness of boards - 2 see the Thickness basic reek (two big, on all height of a rack and one short, from the face party of two bottom shelves) - 4-6 see As a support at a wall are used bearing rejki 3-4 x 2,5 sm in a diameter. They privertyvajutsja screws or it is direct to a wall (preliminary in it it is necessary to build in plastic shkanty) or to vertically established board attached to a wall which width corresponds to width of our shelves. .

In last variant necessity to hollow out or drill in a wall set of apertures disappears. Basic racks are connected to boards of shelves in such a manner that they vpoldereva enter into them. For this purpose it is necessary, that after an exact marking of the sizes (a thickness of a board and distance between racks) nozhovkoj corresponding cuts have been made. Then on either side of these cuts the sharp chisel hollows out dredging. Basic rejki and boards strongly incorporate among themselves glue cold otverzhdenija. The fastening with plinths is the most expedient for making by means of screws (preliminary having done an aperture vertical drill under them that heads of screws were level with a board surface). Then all edges are processed by a coarse-grained emery paper. It is necessary to note, also, that regiments from outside walls correspond it skosu. .

Now we will pass to pristennomu to a table. Its sizes also are defined by the area which for it is allocated. In our case it is calculated on three persons. Though usually the table has a squared shape, here one party is parallel skosu walls as it is an optimum variant of use of the area. The table consists of two plates (is better from dveresnostruzhechnyh plates (DSP), connected from outside walls a board the in width 12-15 cм by means of glue and screws (it is possible to use and nails). In this place the table leans on rejki, privernutuju to a wall screws and shkantami. Thus the intermediate shelf should be connected strongly with rejkoj from below by means of iron squares owing to what the design will be much stronger. .

From the forward party the table leans on two legs (section 6x6 sm) into which plates enter. Eyes (as at a rack) are for this purpose cut out the corresponding width. In this case at processing we should refuse a saw as legs are established on corners of plates with some inclination. The general height of a table should not exceed 70-75 see .

The Distance between a wall, accordingly a rack and a table, should be not less than 70-80 sm that it was possible to move chairs freely.

If at the equipment of a table we will refuse the bottom plate, there is a necessity for giving to a table corresponding stability by means of crossbeams. Instead it is possible to use however tsargi in the width a minimum 15 the second plate see However has the big practical advantage as on it it is possible to put paper napkins, napkins for tablewares and t.d that they always were near at hand. In drawing the scheme of the rack separating nashumalenkuju a dining room from other part of kitchen at the left is represented.
If at the equipment of a table we will refuse the bottom plate, there is a necessity for giving to a table corresponding stability by means of crossbeams. Instead it is possible to use however tsargi in the width a minimum 15 the second plate see However has the big practical advantage as on it it is possible to put paper napkins, napkins for tablewares and t.d that they always were near at hand. In drawing the scheme of the rack separating nashumalenkuju a dining room from other part of kitchen at the left is represented.