furniture the hands how to make furniture the hands furniture the hands - the main page the main page - furniture the hands furniture manufacturing by the hands furniture manufacturing by own strength
offers on furniture manufacturing by the hands how to make furniture the hands furniture the hands, articles furniture the hands, councils recommendations how to make furniture the hands councils how to make furniture the hands furniture the hands a management how to make furniture the hands

the Section case in a sleeping room

If possibilities the apartments much willingly allow equip a separate sleeping room. Despite it, it is necessary to try to equip a premise so that it added with few other pieces of furniture, it could be used as universal. For this purpose we suggest to issue a sleeping room in a little original image.

In our example we recognise that one wall is occupied by a case for top and bed-clothes in height to a room ceiling. Opposite to this wall there are not usual beds, and one very wide couch or two usual mattresses on legs, nearby. The couch headboard is framed by two section cases. This variant can easily execute and the beginning joiner - the fan.

As a material for the main support we use available in sale rejki which can be a different thickness. For our variant we take rejki in the thickness 4 x 4 sm, and for shelves - drevesnostruzhechnye plates (DSP) 1,8X2 see in the thickness However quite probably to use for cross-section shelves kleenuju wood or plywood plates from old furniture not used at present. .

We Will divide in the beginning a case according to the set sizes. Distances between regiments on width and height can be very uniform and symmetric, and can be chosen is underlined by the dissymetric. In drawing one of such variants is presented. At a construction of a case we mean a room in the new apartment, having height approximately 250 Depth of our case as we will agree see, will not exceed 35 see .

Through the established intervals of intermediate shelves we will insert between pair basic reek cross-section rejki. Rigid connection is carried out by thorns or shkantami. If screws over them the small decorative metal caps which are usually lined to a bottom of legs of chairs jam are used. When separate basic parts are connected, we cut out plug-in regiments, we cut them for the thickness vertical reek and we stack regiments between basic parts. Regiments which are looked through from above, fasten from below, and what are looked through from below fasten from above thin screws. In places which are not looked through, it is possible to attach a case to a wall by means of probes. .

Especially effectively the case looks, thanks to partially closed branches sideways or in front. (In drawing they are designated by vertical strokes). For this purpose between decorative nails or screws the decorative cord stretches, and it is necessary, that full colour conformity with regiments was observed. As a material it is better to use thin rejki. This though also differentiating, but nevertheless transparent facing should is established so that without breaking it, it was possible to get into all corners of our new furniture. .

As is shown in the top drawing, in the right compartment the small toilet little table can be equipped. Under it the board against which the little table leans settles down, departing from little table edge in depth on 5-10 see Over a low toilet little table is hung up the big mirror allowing us to use by it and sitting (especially to ladies to direct cosmetics) and standing, when it is possible to check up a kind of the clothes. .

Probably, someone considers this half-internal design as a toy as overindulgence, however the sensation of grace brought in a premise by this design, represents a worthy counterbalance to the made narrower, compact furniture wall located on an opposite side of a room. Therefore it is not necessary to fill this case things to a limit. Books, glass, ceramics and pictures, - all it, certainly approaches to separate compartments, however it is necessary to watch that it was not created impressions that regiments are overloaded. Besides it is possible to try the design variant, which height twice below level of a ceiling of a room.

In drawing the principle of placing of a cord at the left is represented. Knots are fastened in the beginning and the piece end. The cord is passed through carnations and stretches.
In drawing the principle of placing of a cord at the left is represented. Knots are fastened in the beginning and the piece end. The cord is passed through carnations and stretches.