furniture the hands how to make furniture the hands furniture the hands - the main page the main page - furniture the hands furniture manufacturing by the hands furniture manufacturing by own strength
offers on furniture manufacturing by the hands how to make furniture the hands furniture the hands, articles furniture the hands, councils recommendations how to make furniture the hands councils how to make furniture the hands furniture the hands a management how to make furniture the hands

In the beginning a cradle, then a bed

And what young mother does not want, that in a room was a few romanticists? The cradle for the kid in full degree corresponds to these representations. However the shaking cradle is suitable only for the first months of his life. When the child starts to become independent, its bed should be fixed.

In our example the cradle and a bed are almost united. To make from first second does not make special work and does not demand any special expenses. Only roundish bottom kolodki replace with strongly fixed supports, and our child can develop the temperament in this small kingdom, without giving to troubles to parents attempts to drop out of a cradle. .

In the beginning we will talk about a design of the bed which are general for both variants. As basic elements two plates of the identical sizes for forward and back backs and two frames from the sides, connected with both parties rejkami or bruskami are necessary to us. The sizes of this basic part can vary on length, between 120 and 140 sm and on width - between 6о and 70 see For the face parties is better plywood plates not less than 2-2,5 approach in the thickness see It is possible to use also drevesnostruzhechnye plates (DSP) or the frames which have been pasted over from both parties with firm wood-fiber plates (TDVP). .

The Parties, are made from reek in the thickness, a minimum of 2 sm and width 7-8 sm connected in a frame. Connection is carried out by means of thorns and eyes or vnahlestku. At pasting it is necessary to pay attention to that frames bylitochno at right angle and for shvatyvanija glue settled down on an equal surface.

Frames for lateral parts are measured so that below they were up to standard of a headboard (according to other face part), and from above were more low approximately on 5 see .

Vertical reechnye connections are carried out in the form of a lattice and create simultaneously a decorative element. For this purpose there are some possibilities. For example, rejki precisely are framed and incorporate to its long parts by means of thorns or shkantov or become stronger then outside. In the first case rejki stick together with a frame. In the second case rejki on the ends are cut approximately on 2,5 sm and act outside. Acting parts follows from above and from below strongly to round or fill up. Distances between vertical parts should be no more than 5-6 see At an arrangement reek outside in addition to glue the flattened probes which, fastening rejki are used, promote increase of stability of a design in case the temperamental child will want to test, are how much strongly established rejki. (Hats of nails, certainly, thus utaplivajutsja, and the formed apertures zashpaklevyvajutsja.) .

Lateral faces strongly incorporate with face to the help shkantov. Besides, for bolshej reliability it is recommended to fix a design below and above, vrezannymi in wood squares. All it should be made very accurately completely to exclude danger of that the child will then be wounded about any keen edge or a ledge. For this purpose it is necessary, that all edges and corners have been slightly rounded, and then filled up by means of a fine-grained emery paper. The bed floor is carried out from boards in the thickness of 1,5 sm which keep within on privernutye screws to lateral faces bearing rejki. .

Roundish bottom kolodki for a cradle cut out from wood in the thickness not less than 3 sm, and zakruglenie should be flat that the cradle at its rocking has not overturned. These parts the same as also steady kolodki which will come of them in the stead, incorporate to a headboard (according to other face party) with the help shkantov. Height of these kolodok - approximately 25 sm and as it is already told, they should be very steady to what drawing below at the left testifies.

the variant Represented in drawing shows one more possibility of registration bokovin beds. Here vertical rejki fasten on a frame only outside. The truth because of the thickness they look a little toporno. However it can promote and to the stylised registration of a bed if for example, instead of colouring to leave untouched the natural invoice of wood or to decorate the face parties with a burning out on a tree.
the variant Represented in drawing shows one more possibility of registration bokovin beds. Here vertical rejki fasten on a frame only outside. The truth because of the thickness they look a little toporno. However it can promote and to the stylised registration of a bed if for example, instead of colouring to leave untouched the natural invoice of wood or to decorate the face parties with a burning out on a tree.